Mounting: Physical Properties

ambient mounting

ProductSystemPropertiesColourTimeExothermic
peak		Use with a
pressure vessel
or vacuum system
Technovit 40003 components-Cures rapidly.
-Low shrinkage.
-Excellent edge retention.
-Excellent abrasion resistance.
-Excellent flow behavior.
Opaque10 min122 °CYes
Technovit 4002 IQ2 components-Cures rapidly.
-Low shrinkage.
-Excellent edge retention.
-Excellent abrasion resistance.
-Excellent flow behavior.
White15 min99 °CNo
ProductSystemPropertiesColourTimeExothermic
peak		Use with a
pressure vessel
or vacuum system
Technovit 40062 components-Longer polymerization time.
-Good for sensitive material.
-Excellent for visual inspection.
-Reduced the polymerization heat by -10%.
-Reduced shrinkage.
Routine preparation.
Transparent9-12 min99 °CNo
Technovit 40042 components-Cures rapidly.
-Some shrinkage.
-Good edge retention.
-Variable mixing ratio.
-Routine preparation.
Transparent9-12 min99 °CNo
Technovit 40212 components-Reduced shrinkage.
-Good edge retention.
-Cures rapidly.
-Less pollutant.
-Low viscosity.
-Odorless.
-Fewer air bubbles.
Black5-6 min99 °CNo
Technovit 50002 components-Cures rapidly.
-Some shrinkage.
-Homogeneous conductive.
-SEM / Probe compatible.
Copper8-10 min125 °CNo
Formula 12 components-Cures rapidly.
-Some shrinkage.
-Good edge retention.		White transparent9-12 min71 °CNo
ProductSystemPropertiesColourTimeExothermic
peak		Use with a
pressure vessel
or vacuum system
Epoxy2 components-Cures slowly.
-Excellent edge retention.
-Excellent abrasion resistance.
Transparent24 hours90 °CNo
Technovit Epox Fast2 components-Infiltrate porous material.
-Excellent edge retention.
-Excellent abrasion resistance.
-Variable cure time.
Transparent10 hours57 °CYes
Technovit Epox Regular2 components-Infiltrate porous material.
-Excellent edge retention.
-Excellent abrasion resistance.
-Variable cure time.
Transparent18 hours35 °CYes

compression mounting

Product System Properties Colour Time Exothermic
peak		 Use with a
pressure vessel
or vacuum system
Epoxy 1 component -Very hard.
-Excellent edge retention.
-Best infiltration.
-Low shrinkage.
-Resistant to chemical attack.
 Black 8-10 min. 150-180 °C No
Product System Properties Colour Time Exothermic
peak		 Use with a
pressure vessel
or vacuum system
Phenolic, Red 1 component -Routine preparation
-Rapid.
-High shrinkage.
-Fair edge retention.
-Not resistant to chemical attack.
-Can be used as filler.
 Red 8-10 min 150-177 °C No
Phenolic, Black 1 component -Routine preparation
-Rapid.
-High shrinkage.
-Fair edge retention.
-Not resistant to chemical attack.
-Can be used as a filler.		 Black 8-10 min 150-177 °C No
Phenolic, Green 1 component -Routine preparation
-Rapid.
-High shrinkage.
-Fair edge retention.
-Not resistant to chemical attack.
-Can be used as a filler.		 Green 8-10 min 150-177 °C No
Phenolic, Brown 1 component -Routine preparation
-Rapid.
-High shrinkage.
-Fair edge retention.
-Not resistant to chemical attack.
-Can be used as a filler.		 Brown 8-10 min 150-177 °C No
Product System Properties Colour Time Exothermic
peak		 Use with a
pressure vessel
or vacuum system
Phenolic, Red 1 component -Routine preparation
-Rapid.
-High shrinkage.
-Fair edge retention.
-Not resistant to chemical attack.		 Red 8-10 min 150-177 °C No
Phenolic, Black 1 component -Routine preparation
-Rapid.
-High shrinkage.
-Fair edge retention.
-Not resistant to chemical attack.		 Black 8-10 min 150-177 °C No
Phenolic, Green 1 component -Routine preparation
-Rapid.
-High shrinkage.
-Fair edge retention.
-Not resistant to chemical attack.
 Green 8-10 min 150-177 °C No
Product System Properties Colour Time Exothermic
peak		 Use with a
pressure vessel
or vacuum system
Diallyl Phthalate, Fibreglass 1 component -Excellent edge retention.
-Low shrinkage.
-Resistant to chemical attack.
 Blue 8-10 min 130-190 °C No
Diallyl Phthalate, Mineral 1 component -Excellent edge retention.
-Low shrinkage.
-Resistant to chemical attack.
 Blue 8-10 min 130-190 °C No
Technotherm 2000, Fiberglass
 1 component -Good edge retention.
-Low shrinkage.
-Resistant to chemical attack.
-Resin is Inorganically filled.
-Excellent filling behaviour.
-No hazardous components.
 White/Grey 10-15 min 160-180 °C No
ProductSystemPropertiesColourTimeExothermic
peak		Use with a
pressure vessel
or vacuum system
Technotherm 30001 component-Graphite filler.
-Electrically conductive.
-Low shrinkage.
-SEM/electropolishing
Black10-15 min160-180 °CNo
ProductSystemPropertiesColourTimeExothermic
peak		Use with a
pressure vessel
or vacuum system
Thermoplastic1 component-Routine preparation.
-Fair edge retention.
-Not resistant to chemical attack.
-Excellent for visual inspection.
Transparent12-15 min140 °CNo

Subscribe

Complete the form below to subscribe to our mailing list and stay updated on news, new product information, and exclusive offers. (Required fields are marked with *).